DALIEye 26 — see what's
happening on the DALI line.
Every frame in plain text, answers with their meaning and a device scan that finds lamp failures, duplicate addresses and devices without an address — according to IEC 62386-102 and -103, via the Lunatone DALI-2 IoT.
DALIEye 26 connects to the gateway over the network and shows all frames of the line decoded and coloured by kind: 16-bit to control gear, 24-bit to control devices, answers matched to the preceding query. The scan reads type, version, GTIN, serial number, levels and groups of every device — without changing the configuration. No installation at hand? The simulation shows what it looks like.
Bus monitor: every query with its answer and what it means, e.g. QUERY STATUS → “lamp off, power cycle seen”. (Image from the program, simulation.)
From the first frame to the finding
For electricians, lighting designers, system integrators and commissioning engineers who check, commission and troubleshoot DALI installations.
Bus monitor in plain text
All frames of the line, decoded according to IEC 62386-102 and -103: target, command and value, coloured by kind — level, command, configuration, query, answer, event, error.
Understand the answers
Every answer is interpreted with the preceding query, e.g. QUERY STATUS → “lamp failure”. “(2×)” marks configuration commands repeated within 100 ms — as the standard requires.
Device scan
Reads every short address 0–63: device type, DALI version, GTIN, serial number, firmware, levels, groups and optionally scenes — for control gear and 24-bit control devices such as push buttons and occupancy sensors.
Findings at a glance
Lamp and gear failures, duplicate addresses, devices without a short address and missing answers appear right in the device list — with all details of the selected device next to it.
The scan changes nothing
It only sends queries and writes to the volatile DTR registers at most. The installation's addresses, groups and scenes stay as they are. For 64 devices it takes about 2–6 minutes.
Send frames
Send your own 16- or 24-bit frames and see the answer right away. “Identify” makes a DALI-2 device flash so that you can find it in the ceiling.
Record and analyse
Record all frames continuously, even while the display is paused, and open them again later. Filter by address, command or hex, “Errors only”, statistics — and export as CSV.
Find the gateway, practise without a site
The search finds the Lunatone DALI-2 IoT in your own networks, also over VPN. The simulation recreates a line with typical findings — for trying it out and for training.
Also: addresses from 0 or from 1 · bus power status · light/dark · 19 languages · automatic updates · works with the Eye Suite 26
An overview in three steps
DALIEye shows the same steps under “Help & basics”.
Standard, gateway, formats
| Standard | IEC 62386-102 (control gear) and -103 (control devices), DALI-2 and DALI-1 |
| Frames | 16-bit to control gear (A = short address, G = group), 24-bit to control devices (D = short address, DG = device group), 8-bit answers |
| Gateway | Lunatone DALI-2 IoT (art. no. 89453886), also IoT4, via the WebSocket interface, firmware v1.2 or later |
| Addresses | Short addresses 0–63, groups 0–15; display from 0 or from 1 |
| Scan | Type, DALI version, levels, groups, scenes (optional), random address, memory bank 0 (GTIN, serial number, firmware) |
| Recording | continuous as .jsonl, can be opened again later |
| Export | Frames and scan result as CSV |
Good to know: The gateway delivers frames that are already decoded. Signal quality (bit timing, edges) and bus voltage in volts cannot be measured this way — that needs a measuring device directly on the bus. The time stamps come from the gateway and are suitable for intervals in the millisecond range.
Six typical jobs
Inventory
Which devices are on the line, with which address, version and group? The scan delivers the list, the CSV export the documentation.
Check commissioning
Do the controller's commands arrive, and how do the devices respond? The bus monitor shows every command and every answer in plain text.
Find duplicate addresses
Colliding answers reveal short addresses used more than once; the scan detects devices without an address on the bus.
Troubleshooting
Lamp failure, missing bus power, framing errors or a device that does not answer — DALIEye shows where things go wrong.
Sporadic problems
The recording keeps running in the background. Open it later, filter it and see what was on the line at the time of the fault.
Training
The simulation shows a line with typical findings — ideal for explaining DALI frames and the scan without a real installation.
Try first, license later
Download DALIEye 26 and request a free trial licence. The licence is activated right in the program.
- Windows: a single program file
- Linux x64 and arm64 (Raspberry Pi)
- The program installs updates itself on request
- Free, all features
- Request online, activate in the program
- Annual licence for one computer, 12-month term
- All features, all 19 languages
- Updates included during the term
- Activation right in the program
For a licence, please write to us at info@busbaer.de. The licence is tied to one computer; if you change computers, please get in touch. You receive the licence code by e-mail and activate it right in the program. The Lunatone DALI-2 IoT gateway is not included.
Part of the Eye Suite 26
All Eye tools fit into the free Eye Suite 26: once it is installed, its dashboard shows the licence status of DALIEye 26, and the DALI frames also appear in the suite's combined monitor — together with KNX, Modbus and the other protocols. Started from the suite, DALIEye runs right inside the suite window. Without the suite, DALIEye 26 works just the same.
On Windows, DALIEye 26 asks once on first start whether it should install itself to C:\Program Files\Alexander Maier GmbH\DALIEye 26\, and creates shortcuts on the desktop and in the Start menu. This needs administrator rights once; later updates run without them.
Gateway, Windows and Linux
| Hardware | Lunatone DALI-2 IoT (or IoT4) with firmware v1.2 or later and a DALI bus power supply on the line. Without a gateway only the simulation runs. |
| Windows | 64-bit |
| Linux | 64-bit: x64 for PCs, arm64 e.g. for Raspberry Pi 4 or 5 with Raspberry Pi OS 64-bit (Bookworm or later) and desktop. 32-bit systems are not supported. |
| Installation | Windows: a single program file, .NET included; on first start the program offers to install itself to C:\Program Files\Alexander Maier GmbH\.Linux: tar xzf DALIEye26-linux-<arch>.tar.gz, then run bash install.sh in the unpacked folder — afterwards start it from the menu or with dalieye26 in a terminal |
| Network | PC and gateway on the same network or reachable via VPN; the WebSocket connection to the gateway must not be blocked by a firewall or proxy |
| Internet | for licence activation and updates |
After that, the program updates itself on request. There is no macOS download yet.
Frequently asked questions
Which gateway do I need?
The Lunatone DALI-2 IoT (art. no. 89453886) or the IoT4 with firmware v1.2 or later. DALIEye connects via its WebSocket interface. The gateway needs a DALI bus power supply on the line and can keep doing its own tasks (automations, app) alongside.
How can I try DALIEye?
Download the program and request a free trial licence via “Request trial licence” on this page; you activate it in the program. Without a gateway, the simulation shows a line with typical findings.
Does the device scan change the installation?
No. The scan only sends queries and writes to the volatile DTR registers at most. Addresses, groups, scenes and levels stay unchanged. Only “Send frame” and “Identify” act on the installation — and only when you trigger them.
How long does a scan take?
About 2–6 minutes for 64 devices, depending on the installation and network. DALIEye reads scenes only if you select it.
Which findings does DALIEye detect?
Lamp and gear failures from QUERY STATUS, addresses used more than once (the answers to device-specific queries collide), devices without a short address on the bus and missing answers when a DALI-2 device does not deliver memory bank 0. Devices without a short address are detected but not yet listed individually.
What does “(2×)” mean in the bus monitor?
The frame was repeated within 100 ms. According to the standard, configuration commands must arrive like this for a device to execute them. Without the repetition, the device ignores the command.
Can DALIEye measure signal quality or bus voltage?
No. The gateway delivers frames that are already decoded. Bit timing, edges and the bus voltage in volts cannot be measured this way — that needs a measuring device directly on the bus. DALIEye does show whether bus power is present.
What if the gateway is not found?
PC and gateway must be on the same network. Over VPN the search only works if the tunnel includes the gateway’s network — otherwise enter the address manually. If DALIEye reports “WebSocket not possible”, check the gateway firmware (v1.2 or later) as well as firewall and proxy.
Does DALIEye run on Linux or Mac?
Linux yes: packages for x64 and arm64, also for the Raspberry Pi 4 or 5 with Raspberry Pi OS 64-bit. There is no download for macOS yet.
Do I have to install anything?
On Windows, DALIEye is a single program file. On first start it asks once whether it should install itself to “C:\Program Files\Alexander Maier GmbH\DALIEye 26\” and creates shortcuts; this needs administrator rights once. On Linux you unpack the archive and run install.sh.
Can I transfer the licence to another computer?
The licence is tied to one computer. If you change computers, please get in touch with us.
What does DALIEye have to do with the Eye Suite 26?
If the free Eye Suite 26 is installed, its dashboard shows the licence status of DALIEye 26, and the DALI frames also appear in the suite’s combined monitor. Started from the suite, DALIEye runs inside the suite window. Without the suite, DALIEye works unchanged.
Which languages are available?
The user interface is available in 19 languages.
Another question? Write to us at info@busbaer.de.
See what's happening on the DALI line.
Download DALIEye26.exe, request a trial licence — and see your first frames within minutes, with the gateway or the simulation.
Get in touch
Imprint
Alexander Maier GmbH
Beckstraße 3
D-69412 Eberbach
Managing director: Alexander Maier
Registered office: Eberbach
Register court: Mannheim
Commercial register: HRB 335404
VAT ID: DE177682654
Phone: +49 (0) 6271 – 91 94 70
E-Mail: info@busbaer.de